|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
33.02mm [1.300"] NC 47 37 GND 48 38 1 2 36 35 33.02mm [1.300"] 11 12 26 25 14 24 Top View 13 23 10.36mm [0.408"] Side View SK-UGA8/49A-03 SF-MLF48A-A-02 Description: Carrier Adaptor 48 position MLF ZIF socket to 48 position surface mountable MLF emulator foot with test probes. Pin assignment/ interconnect 1:1. PAGE 1 of 2 Tolerances: diameters 0.03mm [0.001"], PCB perimeters 0.13mm [0.005"], PCB thicknesses 0.18mm [0.007"], pitches (from true position) 0.08mm [0.003"], all other tolerances 0.13mm [0.005"] unless stated otherwise. Materials and specifications are subject to change without notice. CA-MLF48A-A-Z-T-01 Drawing (c) 2004 IRONWOOD ELECTRONICS, INC. PO BOX 21151 ST. PAUL, MN 55121 Tele: (651) 452-8100 www.ironwoodelectronics.com Status: Released Drawing: H. Hansen File: CA-MLF48A-A-Z-T-01 Dwg Scale: 2:1 Rev: B Date: 6/29/04 Modified: 4/14/05 Recommended torque = 1.5 in. lbs. (24 in. oz.) MLF foot Top view (not to scale) 3 22.08mm [0.869"] board UGA SK-UGA8/49A-03 1 SF-MLF48A-A-02 2 1 MLF pin 1 (target board) Gnd, index pin 2 Apply torque and then plug into SF-MLF foot. NOTE: Do not apply torque when assemby is pluged into SF-MLF foot. MLF foot Top view (not to scale) 1 2 3 Substrate: 2.34mm 0.18mm [0.092" 0.007"] FR4/G10 or equivalent high temp material. 17m [1/2 oz.] Cu clad. SnPb plating. Pins: material- Brass Alloy 360 1/2 hard; finish0.25m [10"] Au over 1.27m [50"] Ni (min.). Test points: material- Phosphor Bronze; platingSn over 1.27m [50"] Ni. Gold flash on contact end. User Instructions: 1. Attach SF-MLF48A-A-02 foot to the target board. 2. Turn plastic thumb screws until head touches bottom of CA-MLF48A-A-Z-T-01 board. 3. Insert SK-UGA8/49A-03 into board UGA. Check orientation. 4. Remove socket lid and compression plate. 5. Insert MLF package into IC guide inside socket cavity. 6. Put compression plate and socket lid in place. 7. Hold socket assembly and apply recommended torque. 8. Carefully insert CA-MLF assembly into SF-MLF feet UGA. Check orientation. 9. Unscrew plastic thumb screws until they hit target board. PAGE 2 of 2 CA-MLF48A-A-Z-T-01 Drawing (c) 2004 IRONWOOD ELECTRONICS, INC. PO BOX 21151 ST. PAUL, MN 55121 Tele: (651) 452-8100 www.ironwoodelectronics.com Status: Released Drawing: H. Hansen File: CA-MLF48A-A-Z-T-01 Dwg Scale: 2:1 Rev: B Date: 6/29/04 Modified:4/14/05 |
Price & Availability of CA-MLF48A-A-Z-T-01 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |